熱搜關鍵詞： 常溫耐磨試驗機 N型熱電偶（NiCrSi-NiSiMg）使用注意事項熔塊爐耐火澆注料流變測定儀

您的位置： 洛陽賽特瑞高溫實驗爐Sintering Furnace首頁 > 高溫電爐系列 > High Pressure Tube Furnace with Optional Alloy Tube(900℃or 1100℃max heat temp.)OTF-1200X-HPV -

High Pressure Tube Furnace with Optional Alloy Tube(900℃or 1100℃max heat temp.)OTF-1200X-HPV

產品型號：High Pressure Tube Furnace with Optional Alloy Tube(900℃or 1100℃max heat temp.)OTF-1200X-HPV

電爐類型：高溫電爐系列

電爐規格：

加熱溫度：

電爐系列：高溫馬弗爐

應用范圍：。

在線咨詢

聯系電話

產品簡介 / Introduction

High Pressure Tube Furnace with Optional Alloy Tube (900℃ or 1100℃ max heat temp.) - OTF-1200X-HPV

OTF-1200X series high-pressure split tube furnaces can be chosen from two kinds of alloy tube, e.g. Stainless steel 310S refractory alloy or Ni-based superalloy, which offer a solution of heating treatment under high positive pressure with/without inert gas support to process special compound material. The furnace can be heated up to the max. 900℃or 1100℃with the optional vessel. The operating positive pressure is from 105 to 800 psi according to different heating temperature. 、Heating temperature up to max. 900℃or 1100°C, Depends on tube alloy 、Stainless steel or nickel-base superalloy processing tube is included ( please choose from product optional ) 、Max pressure up to 800 PSI.depended on tube alloy 、Double layer steel casing with air cooling to keep furnace surface temperature lower than 60°C. High purity fibrous alumina insulation for Max. energy saving 、PID automatic control with 30 steps programmable. Automatic overtemperature and thermally broken protection 、One set of high positive pressure flange 、The pressure sensor is installed in the flange. The pressure will be displayed in the pressure controller in the front panel of the furnace. The alarm system is built in the pressure controller which allow the user to set up the high and low limit point of pressure. When the measuring pressure exceeds the limit point, the alarm strobe and whistle will be activated for warning 、The furnace is able to be controlled by a computer. And the software and USB cable are included

SPECIFICATIONS

	OTF-1200X-HVHP-80(60)-SS	OTF-1200X-HVHP-60-GH
Process Vessels (Pls select the tube size in options bar)	SS310S Stainless Steel alloy80mm O.Dx70(±2) mm I.Dx1000 mm L or 60mm O.Dx50(±2)x1000 mm L	Ni-based superalloyGH747 (Click to download GH747 nickel-based alloy datasheet) OD 60xID 52xLength 1000 (mm)
Copper gasket	For 80mm O.D tube:99 O.Dx82 I.Dx2.2mmFor 60mm O.D tube:82 O.Dx63.6 I.Dx2.2mm	For 60mm O.D tube:82 O.Dx63.6 I.Dx2.2mm
Working Pressure vs. Working Temperature	577 PSI max at ≤500℃511 PSI max at ≤600℃428 PSI max at ≤700℃203 PSI max. at ≤800℃116 PSI max at ≤900°CAttention: Never heat up above 900℃900℃max.for ＜ 1hr	580 PSI (4 Mpa) max. at ≤800°C362 PSI (2.5 Mpa） max. at ≤900°C174 PSI (1.2Mpa) max. at ≤1000°C116 PSI (0.8 Mpa) max. at 1100°CAttention: Never heat up above 1100°CThe furnace also can reach high vacuum up to 10-6 torr by turbopump.
Pressure Measurement Range	0~15Mpa	0~15Mpa
Max. Heating Temperature	900°C	1100°C
Working Gases	Inert gas amp; Hydrogen	Inert gas, hydrogen, and oxygen
Heating Temperature	1100℃max.for ＜ 1hr 800℃continuous	1100℃max.for ＜ 1hr 1000℃for continuous
Heating Rate	≤30°C/min	≤20°C/min
Heating Element	Fe-Cr-Al Alloy doped by Mo	Fe-Cr-Al Alloy doped by Mo
Heating Zone	Total length: 440mm Single zoneConstant temp. zone: 150mm ±1°C	Total length: 440mm Single zoneConstant temp. zone: 150mm ±1°C
Temperature Control	PID control method with over-temp protectionTemperature stability: ±1°CDemo video here)	PID control method with over-temp protectionTemperature stability: ±1°CDemo video here)
Thermocouple	Omega 3mm OD K Typewith high-temperature tolerance (220°C) connector	Omega 3mm OD K Typewith high-temperature tolerance (220°C) connector
Positive Pressure Sensor	Installed in high-pressure flange	Installed in the high-pressure flange
PC Control (Optional)
Pressure Alarm System	The upper limit and lower limit control methodAlarm strobe and warning whistle	The upper limit and lower limit control methodAlarm strobe and warning whistle
Voltage	AC 220V 50/60Hz	AC 220V 50/60Hz
Power	2.5KW(20A breaker required)	2.5KW(20A breaker required)
Application Notes	、The heating temperature must be limited by the certain pressure level due to vessel material strength. Please refer to the specifications 、The pressure increases while the temperature is rising during operation. So you need to calculate the pressure changing towards your target temperature and set a safe value of pressure during the process 、The furnace uses a tube with conflate designed flanges. 、Note: Please never use ordinary SS tube to connect to gas-inlet for using gt; 5Mp pressure, which may cause tube exploded. 、The safety pressure relief valveis available to be installed at the downstream side. Please click here for details. 、A small quartz or Alumina boat should be used to load the sample into the vessel. Please click the link below to order separately. Never place the sample directly onto the vessel without a crucible. Vessel service-life could be reduced significantly if you do so. ?You may use gold or nickel foil to wrap the crucible boat to minimize the contamination to the pressure vessel. ? 、Optional torque wrench is available hereto avoid overtightening the flange bolts ? 、To measure the electric properties ofthermoelectric ceramics under high pressure amp; temperature conditions, pleaseorder alumina testing fixture and high-pressure electrical feedthrough (10Mpa Max.) with the furnace (additional fee will apply). ?
Safety Note	、Ni-based Superalloy ( Waspaloy or equivalent) is a reliable processing tube which can be used under high temperature and high pressure. It has excellent ductility and tensile property so only creep deformation happens under overpressure destruction test and following by a crack formed (usually at the hot zone at the center of the tube) to release the pressure. Brittle fracture won’t happen in the overpressure destruction test which means no tube explosion will happen under the overpressure of inert gas or safe gas or under other accidents causing overpressure of inert gas or safe gas. The pics show Ni-based Superalloy tube under overpressure test 、Attention: For the use with flammable, toxic or corrosive gas, you must contact STR-engineering group for the consultation to know all the prerequisites and precautionary measures. 、Attention: A two-stage pressure regulator must be installed on the gas cylinder to limit the pressure to below 3 PSI for safe operation. Please click here to learn how to install the gas regulator. 、Do not over tightening the flange screws as this may cause permanent damages to the flange or screws. Please refer to the instructions about proper torque for installing CF flange bolts. We recommend you use atorque wrenchto tighten the screws with the flange.
Operation Instructions
Warranty	One-year limited manufacturer warranty with lifetime support (Consumable parts such as processing tubes, o-rings, and halogen lamps are not covered by the warranty, please order replacements at related products below).

STANDARD PACKAGE

P/N	Name	Qty	OTF-1200X-HVHP-60	OTF-1200X-HVHP-80	OTF1200X-60UV
	Tube Furnace main machine	1	√	√	√
	Processing vessel	1	SS310S alloy - 60	SS310S alloy - 80	Ni based alloy-60
	High-pressure flange set (1 pair)	1	√	√	√
ORing-Cu82	Oxygen-free copper gasket	3	√	√	√
MTS02	USB cable and software for temp management	1	√	√	√
FLG-kit-2	Furnace hook	1	√	√	√

import(/layout/smh/menubottom.html);

井式真空光亮退火爐小型坩堝鹽浴爐高溫陶瓷抗彎強度試驗機高溫?zé)嶂貎x

滑軌爐 1200℃大口徑滑軌爐管式快速退火爐滲碳爐爐蓋總成

免責聲明：本站介紹內容（包括產品圖片、產品描述、技術參數等），僅供參考。可能由于更新不及時，或許導致所述內容與實際情況存在一定的差異，請與本公司客服人員聯系確認。內容專業性較強，僅供參考學習，請勿直接采用。本站部分圖片和文字來源于網絡收集整理，僅供學習交流，版權歸原作者所有，并不代表我站觀點。本站將不承擔任何法律責任，如果有侵犯到您的權利，請及時聯系我們刪除。

成功案例Success stories

價格多少錢一臺？

洛陽賽特瑞高溫實驗爐Sintering Furnace始終致力于尖端高溫及加熱產品綜合解決方案。憑借整個集團雄厚的綜合實力、優秀的技術、完善的服務體系，成就了洛陽賽特瑞高溫實驗爐Sintering Furnace可靠的品質。我們生產的質量好，效率高，節能環保，深受國內外廣大客戶的歡迎。價格多少錢一臺? 需要根據詳細技術方案確定

可以加熱到多少度？

是由供應商洛陽賽特瑞高溫實驗爐Sintering Furnace生產的,洛陽賽特瑞高溫實驗爐Sintering Furnace可以加熱到度

溫控表怎么操作?

是由生產廠家洛陽賽特瑞高溫實驗爐Sintering Furnace生產的,可以聯系我們獲得電子版操作說明，以及遠程視頻指導

廠家哪個好?

隨著國內企業生產研發以及高校科研的飛速發展，的需求量日益增加。廠家哪個好?銷售的公司不少，但購買的時候一定要特別注意，要選擇有真正實力，質量可靠，且有專業售后服務團隊的真正生產廠家。本生產廠家洛陽賽特瑞高溫實驗爐Sintering Furnace以高標準、高要求的研發生產理念，確保設備的可靠性！

產品·優勢

PRODUCT ADVANTAGES

外形美觀

外殼由冷軋鋼板折,表面經高速拋丸后靜電噴塑。
密封圈式電纜

可拆卸組合面有密封墊、環、圈、帽。
產品更耐用

推出新型設計方案，結構合理、通用性強、使用壽命高。
按需定制

可按客戶要求定制。

生產基地production base

洛陽賽特瑞高溫實驗爐Sintering Furnace目前共有90余種實驗室設備產品：高溫馬弗爐、、高溫管式爐、氣氛爐、真空爐、熱震爐、結晶爐、火試金爐、箱式爐，常規品足量半成品儲備，快至3個工作日發貨，定制品承諾按期交貨；可根據客戶對產品環境測試的需求，為客戶量身定制性價比高的解決方案及非標定制服務。